Thursday, 28 January 2016

Flashing of GT-I9105P / I9105PXXUBOB2

Firmware GT-I9105P / I9105PXXUBOB2


Model GT-I9105P
PDA Version I9105PXXUBOB2
CSC Version I9105PGBLBOD1
PHONE Version I9105PXXUBNG2
Region GBL
Country Bulgaria 
Build Date 19.02.2015
Changelist 2822071
OS Jelly Bean
OS Version 4.2.2
Flashing requirements:
- Odin Tool (Download)
- Desired firmware package
- Samsung device drivers (Download)

Flashing guide:
1. Download and extract a zip file containing your desired firmware.
2. Open Odin Tool.
3. Boot your device in the "Download Mode":
     Press Volume Down, Power and Home buttons at same time for 5-8 seconds until download mode is active.

4. Connect your device to PC via the USB cable while in download mode.
5. Next, check the "Auto Reboot" and "F. Reset Time" options in Odin Tool.
6. Hit the AP/PDA button then browse and select a tar.md5 file from the extracted folder.
7. Finally press the start button to begin flashing the firmware update on your device.







All The Best
VarunNathan


Saturday, 26 December 2015

External hard drive won't format

External hard drive won't format

Following the below steps at your own Risk....
first open the Command Prompt and type diskpart on it..
now the new window will be open
then carefully the below commands on it with fully understanding the 
below commands.....Best Of Luck.....
Hope it will work 100%.....

DiskPart <ENTER>
list disk <ENTER>
select disk X <ENTER> X=Disk Number
clean all <ENTER> Will take time
list disk <ENTER>
select disk X <ENTER> X=Disk Number
create partition primary <ENTER>
format fs=ntfs quick <ENTER> NO slash
active <ENTER>
exit <ENTER>
exit <ENTER>

Reboot and check Letter assigned in Windows Disk Management

 

Wednesday, 23 December 2015

How do I fix ERR_CONNECTION_REFUSED on Chrome

 Perform the following steps in this particular order:




  1. Open your command prompt as Administrator.
    • In your Start Menu, find "Command Prompt", Right-click on the menu item, and click "Run as administrator".
    • Or, in the Start Menu Search box, type "cmd", then press CTRL+SHIFT+ENTER to run it as Administrator.
  1. Run the following commands in this order (to run each command, press ENTER after typing it):
  1. ipconfig /all
  1. ipconfig /flushdns
  1. ipconfig /renew
  1. netsh int ip set dns
  1. netsh winsock reset
  1. ipconfig /release

Restart your computer, open Chrome and try again. If the error still exists, you have one final option - reinstalling Chrome and starting fresh. This will reset all the remaining variables that may be causing this error:



  1. Clear Google Chrome's cache and cookies. A corrupted cookie or cache file may cause this error to show up. Clear your history, cache and cookies from the "Clear Browser Data..." menu on the Settings page.
  2. Make sure you have unusual toolbars, extensions, viruses or malware. Many malware applications run in the background and prevent Chrome or other web browsers from connecting to external web servers. Uninstall them & use Windows Defender to do a quick/full system scan.
  3. Check/adjust your antivirus and internet firewall settings. Firewall rules (manually or automatically activated) can block incoming and/or outgoing connections for specific ports or applications. Check your antivirus software and/or Windows Firewall settings to make sure that Google Chrome or Ports 80 and 8080 are not blocked in any way.

Restart your computer, open Chrome and try again. If the error persists move on to clearing your DNS resolver cache:

  1. Uninstall Google Chrome using "Add/Remove Programs" or "Programs & Features" from your Control Panel.
  2. Delete all crashreport subfolders. You will find them under C:\Users\%your_name%\AppData\Local\Google\
  3. Reinstall Google Chrome. Download the latest version of Chrome Browser and install it.

Restart your computer, open Chrome and try again. It should work now.

Saturday, 23 May 2015

How to Network Connection Hub

How to Network Connection Hub


A network hub is a device used to connect multiple computers. It is a simple and inexpensive solution when small networks that require file and printer sharing, like ones in homes or small offices, are needed to be made. Most common hubs today support the Ethernet standard. These hubs usually come with 4, 8 or sometimes 16 Ethernet ports.

Materials Needed:
- One (1) 4-port or 8-port 10/100 Mbps Ethernet hub (depending on the number of computers to be networked)
- two (2) or more computers with Windows installed
- 10/100 Mbps Network Interface Cards (NIC) or built-in Ethernet ports installed on each of the computers
- two (2) or more straight through Ethernet cables (depending on the number of computers to be networked)
Step 1
Turn on the computers and wait for Windows to boot properly.
Step 2
Supply the hub with power if the Ethernet hub requires power. Plug the AC power supply into the hub and the power cord into any sufficient power outlet or wall outlet. Most hubs do not have on/off switches and only require to be plugged into an outlet to become active. Make sure that proper voltages are applied to the hub’s power supply to avoid damaging the device. Voltage ratings are typically printed on the underside of the device, alongside the model and manufacturer information.
Step 3
Connect the first computer to the Ethernet hub when all systems are running properly and the Ethernet hub is powered on. Proceed to Step 5 if the computer has a built-in Ethernet port. Proceed to the next step if the computer has no built-in Ethernet port.

Step 4
Install a compatible 10/100 Mbps Ethernet card when the computer has no built-in Ethernet port. Install the drivers of the network card and turn the computer off. Install the network card into the system. Ask for assistance if difficulty in the installation is encountered. Boot up the system when the hardware installation is finished. Follow succeeding instructions that may appear in the Operating System after restarting the computer to install the network card properly.
Step 5
Take the Ethernet cable and plug one end into the computer’s port when an Ethernet port is already available in the system. Plug the other end into one of the network hub’s ports. Make sure the ends are plugged in tightly and properly.
Step 6
Repeat Steps 3 to 5 to connect the other computers to the network. It is then time to configure the systems when all computers are connected to the network hub.
Step 7
Open the Local Area Connection Properties of the system. In Windows’ Control Panel (click Start > Control Panel), look for the Network Connections icon. Double click on the icon to view all available network connections. An icon for a Local Area Connection should be available if the network card was properly installed and is properly working. Right click on the icon and select Properties. Under the General tab, a small area should show the available protocols Windows is using. Look for Internet Protocol (TCP/IP), click on it, and then click on the Properties button just under the selection.
Step 8
The Internet Protocol (TCP/IP) Properties window now appears on the screen. Select 'Use the following IP address:' by clicking the radio button beside it in the General tab. Type in the IP address and Subnet Mask for the system. Typical IP addresses for small home networks have the pattern 192.168.0.X, where X can be any number from 1 to 127. The Subnet Mask for this network will be 255.255.255.0. Click on OK to close the current window. Click on Close to exit the Local Area Connection Properties.
Step 9
Repeat Steps 7 and 8 for each computer connected to the hub. Each computer must have different IP addresses in Step 8 but the Subnet Mask for all computers must be the same. The systems are now ready for sharing files across the network after Steps 3 to 8 are successfully done.

Saturday, 29 November 2014

HACK WIFI PASSWORD USING CMD


1 Go to Start. In the search box, type in "cmd". If your Start menu has the Run command, click Run and type "cmd" in the field.
2 Type"ipconfig" using the cursor.
3 Hit Enter. On your screen, you will see a series of names and numbers. Look for the line that says Default Gateway. Write down the number that you see next to Default Gateway
4 Navigate to Google or another search engine. In the address bar, type in the number that you just wrote down.
5 Hit Enter. You will see another screen that has fields to enter your username and password. The username is "admin", and the password is either "admin" or "1234". Enter that information into the appropriate fields. Click the "Log In" button.
6 Go to the Wireless tab on the website that pops up. If you scroll down, you should find something called password. Write down your password and put it in a safe place in case you forget it again.

You have also

In cmd write ipconfig/hackermode and press enter....
u wil get two options 1 and 2 
press 1 and automatically d wifi password wil be save in ur desktop as a txt file...try it

How to hack wifi password

Wifi Hack using CMD


THE RED COLOUR WORDS ARE CODES.............

Open cmd to open cmd type cmd in run.

At the command prompt type 

netsh wlan show network mode=bssid

available wifi network



How to connect wireless network

Type

netsh wlan connect name=(wifi name )

netsh wlan connect name=Mynet Sata1


press enter your wifi is connected







Some important code :


How to disconnect to a Wireless Network

 netsh wlan disconnect

 How to show available Wireless Network profiles your PC

 netsh wlan show profile

 How to Saves wlan profiles as XML files to the specified location

 netsh wlan export profile name=Mynet Sata1

How to Block a Wireless Connection

netsh wlan add filter permission=block ssid=netgear networktype=Mynet Sata1

If you want to block this computer from accessing all wireless network use denyall option in the command.

 netsh wlan add filter permission=denyall networktype=adhoc

How to show the blocked network

netsh wlan show blockednetworks

How to show the installed Wireless drivers

Thursday, 27 November 2014

SAMSUNGமொபைல் போன்களுக்கான குறியீட்டுகள்......


1)*#9999# - தங்கள் போனின் சாப்ட்வேர் சார்ந்த தகவல்களை அறிய.
2)#*3849# -தங்கள் சாம்சங் மொபைல் போனை மீண்டும்Rebootசெய்ய.
3)*#06# -சாம்சங் போனின்IMEI (EMI)எண்ணை அறிய. இது மிக முக்கிய ஓர் எண்ணாகும்.
4)#*2558# -தங்கள் போனின் கடிகாரத்தை இயக்க அல்லது நிறுத்த. தங்கள் போனின் மொபைல் போனின் டைமை ஆன் செய்ய அல்லது ஆப் செய்ய.
5)#*7337# -தங்கள் அண்மைகால சாம்சங் மொபைல் போனை அன்லாக் செய்ய(UnLock).
6)#*4760# -தங்களில் போனில்GSM Featuresயை இயக்க அல்லது நிறுத்த.
7)*#9998*246# -தங்கள் போனின் மெமரி திறன் மற்றும் பேட்டரியின் திறனை அறிய.
8)*#7465625# -தங்கள் போனின் கடவுசொல் நிலைமை அறிய.
9)*#0001# -தங்கள் போனின் சீரியல் எண்ணை காண.
10)*#2767*637# -தங்கள் மொபைல் போனை அன்லாக் செய்ய.
11)*#8999*636# -தங்கள் போனின் சேமிப்பு கொள்ளலவு நிலைமையை காண.
12)*#8999*778# -தங்கள் சிம் கார்ட் பற்றிய தகவல்களை அறிய.
13)#*#8377466# -தங்கள்போனின் ஹாட்வேரின் தன்மை மற்றும்Versionயை அறிய.
14)#*3888# -சாம்சங் போன்களின்Bluetoothயின்தகவல்களைஅறிய.
15)#*5376# - ஒரே கட்டளையில் தங்கள் போனின் அனைத்து மெசேஜ்யும் ஒரே கட்டளையில் நீக்க அல்லது அழிக்க.
16)#*2472# -தங்கள் போனின் சார்ஜிங் நிலைமை அறிய.


ஒரு சில கோடுகள் சில போன்களில் இயங்காது.